Communicate with Supplier? Supplier
Cindy Suen Ms. Cindy Suen
What can I do for you?
Chat Now Contact Supplier
Home > Products > DC EMI Filter > DC Single Stage Filter > DC One Stage EMI Filters 100A
DC One Stage EMI Filters 100A
  • DC One Stage EMI Filters 100A

DC One Stage EMI Filters 100A

    Payment Type: T/T
    Incoterm: FOB,CFR,CIF,EXW
    Min. Order: 2 Piece/Pieces
    Delivery Time: 7 Days
Contact Now

Basic Info

Model No.: FT110D/FT111D

Rated Voltage: 110/250VAC

Climatic Category(IEC 60068-1): 25/085/21(-25℃ /+85℃ Damp Heat Test For 21 Days)

Operating Frequency: DC

Test Voltage: 500VDC, 3S(line-line); 500VDC, 3S(line-l

Rated Current: 0.5~300A@40℃

Additional Info

Packaging: Carton

Productivity: 500,000pcs annually

Brand: FILTEMC

Transportation: Ocean,Air

Place of Origin: Jinan

Certificate: ISO9001, CE, UL, TUV, RoHS

HS Code: 8548900001

Port: Qingdao,Tianjin,Beijing

Product Description

Introduction of DC EMI Filters:


Rated current: 0.5~300A

Working voltage: 0~250VDC

Various terminals: wire, solder lug, stud

Custom specific versions on request


Typical Applications:

Suitable for switch power supply, SPC exchange and other DC electric device


Features and Benefits of DC Power Line Filters:

  • General purpose DC filters with good attenuation performance at frequency range 150KHz~30MHz.
  • Compact structure, high performance-cost ratio, easy to install, safe and reliable.
  • FT110D and FT111D series are one-stage common mode filters with almost the same filtering effect, only slight difference according to different current.
  • High voltage versions above 250VDC are also available upon request.


EMI Filter certificates CE RoHS UL


Technical Data of DC Power Line EMI Filters:

DC EMI Filters FT110D FT111D Series Technical Data Sheet


1. Storage of DC EMI Filters:

The DC EMI filters mustn't be left out in the heat of the sun or exposed to the rain, it should be stored in warehouse with good ventilation, surrounding temperature between -30℃ and +65℃ , the highest relative air humidity lower than 90%, and no corrosive liquid or gas.

2. Installation of DC Power Line Filters:

  • DC filters should be installed at power input, and the line inside the chassis be as short as possible to reduce radiated interference.
  • Both input and output lines of DC EMI filters neither be intersected nor be tied up by string.
  • Make sure the mounting flange fully grounded, and keep the ground cable as short as possible if filters are connected to other equipment.
  • If the terminal is stud, please use two spanners to fasten the screw nut when connecting to avoid stud rotating and thus causing changes to the internal circuit and consequently leading to filters arcing, short circuit, broken down or the filtering effect worsened.
  • First use spanner1 to fix the screw nut near the metal case, then use spanner2 to tighten the screw nut in front( shown as Figure1), otherwise the terminals may be damaged.
  • Apply the same for the connection of other phases.

Requests for samples of any catalog item are available for engineering evaluation Free of Charge.


All EMI Filters are RoHS compliant and approvals held include CE, UL,cUL and TUV.

All quality control procedures are fully documented and available for review. FILTEMC is ISO 9001 compliant.



Looking for ideal DC EMI Filters Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the DC Power Line Filters are quality guaranteed. We are China Origin Factory of DC Filters. If you have any question, please feel free to contact us.

Product Categories : DC EMI Filter > DC Single Stage Filter

Email to this supplier
  • Ms. Cindy Suen
  • Your message must be between 20-8000 characters

Related Products List

Home

Phone

Skype

Inquiry