Communicate with Supplier? Supplier
Cindy Suen Ms. Cindy Suen
What can I do for you?
Chat Now Contact Supplier
Home > Products > DC EMI Filter > DC Single Stage Filter > 24VDC-250VDC DC Line Noise EMI Filters with 1-Stage
24VDC-250VDC DC Line Noise EMI Filters with 1-Stage
  • 24VDC-250VDC DC Line Noise EMI Filters with 1-Stage

24VDC-250VDC DC Line Noise EMI Filters with 1-Stage

    Payment Type: T/T
    Incoterm: FOB,CFR,CIF,EXW
    Min. Order: 2 Piece/Pieces
    Delivery Time: 7 Days
Contact Now

Basic Info

Operating Frequency: 50/60Hz

Climatic Category(IEC 60068-1): 25/085/21(-25℃ /+85℃ Damp Heat Test For 21 Days)

Rated Voltage: 110/250VAC

Rated Current: 1-10A@40℃

Test Voltage: 1500VDC, 3S(line-line); 1500VAC, 3S(line-ground)

Additional Info

Packaging: Carton

Productivity: 500,000pcs annually

Brand: FILTEMC

Transportation: Ocean,Air

Place of Origin: Jinan

Certificate: ISO9001, CE, UL, TUV, RoHS

HS Code: 8548900001

Port: Qingdao,Tianjin,Beijing

Product Description

FILTEMC is an international leader in the design and manufacture of standard and customEMI/EMC/RFI Filters.

A wide range of DC Line Noise EMI Filters are available at FILTEMC.


Introduction of DC RFI Filter:

Rated current: 0.5~300A
Working voltage: 0~250VDC
Various terminals: wire, solder lug, stud
Custom specific versions on request


Features and Benefits of DC Line Filter:


  • General purpose DC filters with good attenuation performance at frequency range 150KHz~30MHz.
  • Compact structure, high performance-cost ratio, easy to install, safe and reliable.
  • FT110D and FT111D series are one-stage common mode filters with almost the same filtering effect, only
  • slight difference according to different current.
  • High voltage versions above 250VDC are also available upon request.
Typical Applications of EMI Filter DC Powewr:


Suitable for switch power supply, SPC exchange and other DC electric device


EMI Filter certificates CE RoHS UL


Dc Series Emi Filter Ft110d Ft111d

1. Storage of DC Single Phase Power Line Filters:

  • The DC Line Filters mustn't be left out in the heat of the sun or exposed to the rain, it should be stored in warehouse with good ventilation, surrounding temperature between -30℃ and +65℃ , the highest relative air humidity lower than 90%, and no corrosive liquid or gas.

2. Installation of EMI Filter DC Power:

  • DC RFI Filter should be installed at power input, and the line inside the chassis be as short as possible to reduce radiated interference.
  • Both input and output lines of Inverter filters neither be intersected nor be tied up by string.
  • Make sure the mounting flange fully grounded, and keep the ground cable as short as possible if filters are connected to other equipment.
  • If the terminal is stud, please use two spanners to fasten the screw nut when connecting to avoid stud rotating and thus causing changes to the internal circuit and consequently leading to filters arcing, short circuit, broken down or the filtering effect worsened.
  • First use spanner1 to fix the screw nut near the metal case, then use spanner2 to tighten the screw nut in front( shown as Figure1), otherwise the terminals may be damaged.
  • Apply the same for the connection of other phases.


Requests for samples of any catalog item are available for engineering evaluation Free of Charge.

All EMI Filters are RoHS compliant and approvals held include CE, UL,cUL and TUV.

All quality control procedures are fully documented and available for review. FILTEMC is ISO 9001 compliant.



Looking for ideal DC Line Noise Filter Manufacturer & supplier ? We have a wide selection at great prices to help you get creative. All the DC EMI Filter Design are quality guaranteed. We are China Origin Factory of Dc Motor EMI Filter. If you have any question, please feel free to contact us.

Product Categories : DC EMI Filter > DC Single Stage Filter

Email to this supplier
  • Ms. Cindy Suen
  • Your message must be between 20-8000 characters

Related Products List

Home

Phone

Skype

Inquiry